関係者殿
yama286です
2018.12にラズパイ3 ModelB+を購入し、書籍『RaspberryPiで学ぶ電子工作』で勉強中のものです。1章~10章のうち10章を除き、7章以外はうまくいきました。この間、このコーナに質問させていただき教えていただきありがとうございます。
ところが、7章の7.3『I2C接続するデバイスの例:小型LCD』でLCDに文字を表示する実習で、添付資料に示すように私の推定ですが、ラズパイが壊れたようです。
現象としては、ラズパイの電源で5Vが生きていて、3.3Vが死んでいます(0V)。
ショートさせたつもりはないのですが、突然発生し困っております。
復旧できないのであれば、修理或いは再購入しないといけません。
ご意見お聞かせください。
プログラム名:07-02-LCD_1.py import smbus import time # Define some device parameters I2C_ADDR = 0x27 # I2C device address, if any error, change this address to 0x27 LCD_WIDTH = 16 # Maximum characters per line # Define some device constants LCD_CHR = 1 # Mode - Sending data LCD_CMD = 0 # Mode - Sending command LCD_LINE_1 = 0x80 # LCD RAM address for the 1st line LCD_LINE_2 = 0xC0 # LCD RAM address for the 2nd line LCD_LINE_3 = 0x94 # LCD RAM address for the 3rd line LCD_LINE_4 = 0xD4 # LCD RAM address for the 4th line LCD_BACKLIGHT = 0x08 # On #LCD_BACKLIGHT = 0x00 # Off ENABLE = 0b00000100 # Enable bit # Timing constants E_PULSE = 0.0005 E_DELAY = 0.0005 #Open I2C interface #bus = smbus.SMBus(0) # Rev 1 Pi uses 0 bus = smbus.SMBus(1) # Rev 2 Pi uses 1 def lcd_init(): # Initialise display lcd_byte(0x33,LCD_CMD) # 110011 Initialise lcd_byte(0x32,LCD_CMD) # 110010 Initialise lcd_byte(0x06,LCD_CMD) # 000110 Cursor move direction lcd_byte(0x0C,LCD_CMD) # 001100 Display On,Cursor Off, Blink Off lcd_byte(0x28,LCD_CMD) # 101000 Data length, number of lines, font size lcd_byte(0x01,LCD_CMD) # 000001 Clear display time.sleep(E_DELAY) def lcd_byte(bits, mode): # Send byte to data pins # bits = the data # mode = 1 for data # 0 for command bits_high = mode | (bits & 0xF0) | LCD_BACKLIGHT bits_low = mode | ((bits<<4) & 0xF0) | LCD_BACKLIGHT # High bits bus.write_byte(I2C_ADDR, bits_high) lcd_toggle_enable(bits_high) # Low bits bus.write_byte(I2C_ADDR, bits_low) lcd_toggle_enable(bits_low) def lcd_toggle_enable(bits): # Toggle enable time.sleep(E_DELAY) bus.write_byte(I2C_ADDR, (bits | ENABLE)) time.sleep(E_PULSE) bus.write_byte(I2C_ADDR,(bits & ~ENABLE)) time.sleep(E_DELAY) def lcd_string(message,line): # Send string to display message = message.ljust(LCD_WIDTH," ") lcd_byte(line, LCD_CMD) for i in range(LCD_WIDTH): lcd_byte(ord(message[i]),LCD_CHR) def main(): # Main program block # Initialise display lcd_init() while True: # Send some test lcd_string("Created by <",LCD_LINE_1) lcd_string("Osoyoo.com <",LCD_LINE_2) time.sleep(3) # Send some more text lcd_string("> Tutorial Url:",LCD_LINE_1) lcd_string("> http://osoyoo.com",LCD_LINE_2) time.sleep(3) if __name__ == '__main__': try: main() except KeyboardInterrupt: pass finally: lcd_byte(0x01, LCD_CMD)
回答1件
あなたの回答
tips
プレビュー
バッドをするには、ログインかつ
こちらの条件を満たす必要があります。
2019/05/20 01:08
2019/05/20 01:19
2019/05/20 04:51